PLEN Playground - Wiki

User Tools

Site Tools

You are here: index.html » Tutorials » plen2 » Arm
tutorials:plen2:arm

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
tutorials:plen2:arm [2016/02/18 05:09]
Guvalif 		tutorials:plen2:arm [2016/04/10 12:18]
Guvalif
Line 2: Line 2:
  
 ===== Table of Contents ===== ===== Table of Contents =====
-  - [[introduction]] 
   - [[firmware]]   - [[firmware]]
 +  - [[battery]]
   - [[arm]] **Current section**   - [[arm]] **Current section**
-  - [[foot]]+  - [[leg]]
   - [[head]]   - [[head]]
   - [[body]]   - [[body]]
   - [[merge]]   - [[merge]]
-  - [[wiring]]+  - [[cover]] 
 +  - [[tune]]
  
-Prev > [[firmware]]\\ +Prev < [[battery]]\\ 
-Next > [[foot]]+Next > [[leg]]
 ---- ----
  
Line 20: Line 21:
 ^Name                                                                                                        ^  Q'ty  ^ ^Name                                                                                                        ^  Q'ty  ^
 |[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_assem_type1.stl|servo_assem_type1.stl]]        |  1     | |[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_assem_type1.stl|servo_assem_type1.stl]]        |  1     |
-|[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_horn.stl|serve_horn.stl]]                      |  1     |+|[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_horn.stl|servo_horn.stl]]                      |  1     |
 |[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_bracket_elbow_1.stl|servo_bracket_elbow_1.stl]]|  1     | |[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_bracket_elbow_1.stl|servo_bracket_elbow_1.stl]]|  1     |
 |[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_bracket_elbow_2.stl|servo_bracket_elbow_2.stl]]|  1     | |[[https://github.com/plenproject/PLEN2/blob/master/stl/servo_bracket_elbow_2.stl|servo_bracket_elbow_2.stl]]|  1     |
 |[[https://github.com/plenproject/PLEN2/blob/master/stl/hand.stl|hand.stl]]                                  |  1     | |[[https://github.com/plenproject/PLEN2/blob/master/stl/hand.stl|hand.stl]]                                  |  1     |
-|Servo Motor (160mm)                                                                                         |  1     | +|Servo Motor (Length C)                                                                                      |  1     | 
-|Servo Motor (180mm)                                                                                         |  1     |+|Servo Motor (Length D)                                                                                      |  1     | 
 + 
 +{{ :tutorials:plen2:motors.png?direct }}
  
  
Line 40: Line 43:
 {{:tutorials:plen2:arm:02_attach_upper_arm_2.png?direct}} {{:tutorials:plen2:arm:02_attach_upper_arm_2.png?direct}}
  
-**Attention!**: Please fit the conducting wire through inside a groove on **servo_assem_type1.stl**.+**Attention!**: 
 +Please fit the conducting wire through inside a groove on **servo_assem_type1.stl**.
  
 {{:tutorials:plen2:arm:03_attach_upper_arm_ok.png?direct}} {{:tutorials:plen2:arm:03_attach_upper_arm_ok.png?direct}}
Line 50: Line 54:
 ==== Merge Parts ==== ==== Merge Parts ====
 **Attention!**: **Attention!**:
-Before to merge the parts, you should connect servos' cables and control-board.+Before to merge the parts, you should connect servos' cables and the control-board.
 When it was completed, please turn on both switches and keep the status. When it was completed, please turn on both switches and keep the status.
  
 {{:tutorials:plen2:arm:05_connect_wires.png?direct}} {{:tutorials:plen2:arm:05_connect_wires.png?direct}}
  
-**Attention!**: Please connect the white wire which is owned by a servo to inside of baseboard.+**Attention!**: 
 +Please connect the white wire which is owned by a servo to inside of the control-board.
  
 {{ :tutorials:plen2:arm:05_connect_wires.sub.png?direct }} {{ :tutorials:plen2:arm:05_connect_wires.sub.png?direct }}
 +{{ :tutorials:plen2:turn_on.png?direct }}
 +
 +**Attention!**:
 +Attach a servo-horn to 180[mm] servo. At that time, please check it is placed approximately parallel to edge of the servo.
  
 {{:tutorials:plen2:arm:06_attach_servo_horn.png?direct}} {{:tutorials:plen2:arm:06_attach_servo_horn.png?direct}}
Line 66: Line 75:
  
 ---- ----
-Prev > [[firmware]]\\ +Prev < [[battery]]\\ 
-Next > [[foot]]+Next > [[leg]]
tutorials/plen2/arm.txt · Last modified: 2021/04/01 13:52 (external edit)

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki