This shows you the differences between two versions of the page.
tutorials:plen2:body [2016/04/10 02:05] Guvalif [Parts List] |
tutorials:plen2:body [2021/04/01 13:52] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Body ====== | ||
- | ===== Table of Contents ===== | ||
- | - [[firmware]] | ||
- | - [[battery]] | ||
- | - [[arm]] | ||
- | - [[leg]] | ||
- | - [[head]] | ||
- | - [[body]] **Current section** | ||
- | - [[merge]] | ||
- | - [[cover]] | ||
- | - [[tune]] | ||
- | |||
- | Prev < [[head]]\\ | ||
- | Next > [[merge]] | ||
- | ---- | ||
- | |||
- | ===== Parts List ===== | ||
- | Parts list of the body is enumerated below. | ||
- | |||
- | ^Name ^ Q' | ||
- | |[[https:// | ||
- | |[[https:// | ||
- | |[[https:// | ||
- | |[[https:// | ||
- | |Servo Motor (50mm) | ||
- | |Servo Motor (130mm) - Length B | 2 | | ||
- | |Low Head Screw | 4 | | ||
- | |Screw | ||
- | |[[head|Finished Head]] | ||
- | |[[battery|Control Board with Power Supply]] | ||
- | |||
- | |||
- | ===== Print Detail ===== | ||
- | [[specifications/ | ||
- | |||
- | |||
- | ===== Assembling Process ===== | ||
- | ==== Parts List ==== | ||
- | {{: | ||
- | |||
- | ==== Attach Servos ==== | ||
- | {{: | ||
- | {{: | ||
- | {{: | ||
- | {{: | ||
- | |||
- | **Attention!**: | ||
- | Servos' | ||
- | |||
- | {{: | ||
- | |||
- | ==== Attach the Finished Head ==== | ||
- | **Attention!**: | ||
- | Head-board' | ||
- | |||
- | {{: | ||
- | |||
- | ==== Attach Spacer for Servos ==== | ||
- | {{: | ||
- | |||
- | ==== Attach the Control Board ==== | ||
- | **Attention!**: | ||
- | Control-board' | ||
- | |||
- | {{: | ||
- | {{: | ||
- | |||
- | **Attention!**: | ||
- | Please use normal screws to attach the control-board. | ||
- | |||
- | {{: | ||
- | {{: | ||
- | |||
- | ==== Attach the Brackets ==== | ||
- | **Attention!**: | ||
- | Before to attach the brackets, you should connect servos' | ||
- | When it was completed, please turn on both switches and keep the status. | ||
- | |||
- | {{: | ||
- | |||
- | **Attention!**: | ||
- | Please connect the white wire which is owned by a servo to inside of the control-board. | ||
- | |||
- | {{ : | ||
- | {{ : | ||
- | |||
- | **Attention!**: | ||
- | Attach a servo-bracket to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
- | |||
- | {{: | ||
- | {{: | ||
- | |||
- | **Attention!**: | ||
- | Attach a servo-bracket (mirror) to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
- | |||
- | {{: | ||
- | {{: | ||
- | |||
- | **Attention!**: | ||
- | Attach a servo-bracket to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
- | |||
- | {{: | ||
- | {{: | ||
- | |||
- | **Attention!**: | ||
- | Attach a servo-bracket (mirror) to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
- | |||
- | {{: | ||
- | {{: | ||
- | |||
- | ==== Finished Body ==== | ||
- | {{: | ||
- | |||
- | ---- | ||
- | Prev < [[head]]\\ | ||
- | Next > [[merge]] |