This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
tutorials:plen2:body [2015/10/22 09:10] 127.0.0.1 external edit |
tutorials:plen2:body [2016/04/10 12:50] Guvalif |
||
---|---|---|---|
Line 2: | Line 2: | ||
===== Table of Contents ===== | ===== Table of Contents ===== | ||
- | - [[tutorials/ | + | - [[firmware]] |
- | - [[tutorials/ | + | - [[battery]] |
- | - [[tutorials/ | + | - [[arm]] |
- | - [[tutorials/ | + | - [[leg]] |
- | - [[tutorials/ | + | - [[head]] |
- | - [[tutorials/ | + | - [[body]] **Current section** |
- | - [[tutorials/ | + | - [[merge]] |
+ | - [[cover]] | ||
+ | - [[tune]] | ||
- | Prev > [[legs]]\\ | + | Prev < [[head]]\\ |
- | Next > [[head]] | + | Next > [[merge]] |
---- | ---- | ||
- | < | + | ===== Parts List ===== |
- | ## Parts List | + | Parts list of the body is enumerated below. |
- | |Name |Q' | + | |
- | |: | + | |
- | |servo_bracket_type1 | + | |
- | |servo_bracket_type1_mirror|2 | + | |
- | |servo_horn | + | |
- | |servo_motor | + | |
- | |body_middle | + | |
- | |body_rear | + | |
- | |chest_0_12 | + | |
- | |motor_fix_body | + | |
- | ### Parts forme | + | ^Name ^ Q' |
- | </markdown> | + | |[[https:// |
- | [[https:// | + | |[[https:// |
+ | |[[https:// | ||
+ | |[[https:// | ||
+ | |Servo Motor (Length A) | 2 | | ||
+ | |Servo Motor (Length B) | 2 | | ||
+ | |Low Head Screw | 4 | | ||
+ | |Screw | ||
+ | |[[head|Finished Head]] | ||
+ | |[[battery|Control Board with Power Supply]] | 1 | | ||
- | < | + | {{ : |
- | ## Assembling Procedure | + | |
- | ### Placement | + | |
- | </ | + | |
- | {{: | + | |
- | < | ||
- | ### 1. | ||
- | </ | ||
- | {{: | ||
- | {{: | ||
+ | ===== Print Detail ===== | ||
+ | [[specifications/ | ||
- | < | ||
- | ### 2. | ||
- | </ | ||
- | {{: | ||
- | {{: | ||
- | < | + | ===== Assembling Process ===== |
- | ## Completion | + | ==== Parts List ==== |
- | </ | + | {{: |
- | {{: | + | ==== Attach Servos ==== |
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | **Attention!**: | ||
+ | Servos' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ==== Attach the Finished Head ==== | ||
+ | **Attention!**: | ||
+ | Head-board' | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ==== Attach Spacer for Servos ==== | ||
+ | {{: | ||
+ | |||
+ | ==== Attach the Control Board ==== | ||
+ | **Attention!**: | ||
+ | Control-board' | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | **Attention!**: | ||
+ | Please use normal screws to attach the control-board. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | ==== Attach the Brackets ==== | ||
+ | **Attention!**: | ||
+ | Before to attach the brackets, you should connect servos' | ||
+ | When it was completed, please turn on both switches and keep the status. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Attention!**: | ||
+ | Please connect the white wire which is owned by a servo to inside of the control-board. | ||
+ | |||
+ | {{ : | ||
+ | {{ : | ||
+ | |||
+ | **Attention!**: | ||
+ | Attach a servo-bracket to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | **Attention!**: | ||
+ | Attach a servo-bracket (mirror) to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | **Attention!**: | ||
+ | Attach a servo-bracket to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | **Attention!**: | ||
+ | Attach a servo-bracket (mirror) to the body. At that time, please check it is placed approximately parallel to edge of the body. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | ==== Finished Body ==== | ||
+ | {{: | ||
---- | ---- | ||
- | Prev > [[legs]]\\ | + | Prev < [[head]]\\ |
- | Next > [[head]] | + | Next > [[merge]] |