User Tools
specifications:print_detail:body
Differences
This shows you the differences between two versions of the page.
|
specifications:print_detail:body [2016/03/21 10:45] Guvalif |
specifications:print_detail:body [2021/04/01 13:52] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Body ====== | ||
| - | ===== Table of Contents ===== | ||
| - | * [[arms]] | ||
| - | * [[legs]] | ||
| - | * [[head]] | ||
| - | * [[body]] **Current section** | ||
| - | |||
| - | ---- | ||
| - | |||
| - | ===== Overview ===== | ||
| - | ^ 3D Printer Used ^ Print Region | ||
| - | | Afinia H480 | Body | | ||
| - | | {{h480.jpg? | ||
| - | |||
| - | |||
| - | ===== Files that Need to Print ===== | ||
| - | ==== body_front.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 1 | 0.15 [mm] | 30 [deg.] | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
| - | |||
| - | |||
| - | ==== body_middle.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 1 | 0.2 [mm] | 30 [deg.] | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
| - | |||
| - | |||
| - | ==== body_rear.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 1 | 0.15 [mm] | 30 [deg.] | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
| - | |||
| - | |||
| - | ==== power_switch_holder.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 1 | 0.15 [mm] | 30 [deg.] | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
| - | |||
| - | |||
| - | ==== servo_bracket.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 2 | 0.15 [mm] | --- | Solid | --- | Fine | 31m | | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
| - | |||
| - | |||
| - | ==== servo_bracket_mirror.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 2 | 0.15 [mm] | --- | Solid | --- | Fine | 31m | | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
| - | |||
| - | |||
| - | ==== servo_fixer.stl ==== | ||
| - | ^ Q'ty ^ Z Resolution ^ Part Angle ^ Fill ^ Support Angle ^ Quality ^ Time ^ | ||
| - | | 1 | 0.15 [mm] | 30 [deg.] | ||
| - | |||
| - | === Placement & Result === | ||
| - | {{.body: | ||
| - | {{.body: | ||
specifications/print_detail/body.txt · Last modified: 2021/04/01 13:52 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
